How we build a diagram
Every fuse box on fuses.app is drawn from the manufacturer’s own documents and checked against independent sources before it is published. This page describes how, and what happens when a published value turns out to be wrong.
Where the data comes from
We start with the manufacturer. In order of trust, the sources are:
- Manufacturer documents: the fuse plates and tables in the owner’s manual, the fuse allocation card kept with the box, the label on the fuse box cover, and workshop and body-builder documents.
- Photographs of a real box. A cover label, a fuse card or the position numbers moulded into the housing count as the manufacturer’s word, even where a website’s table of the same car says otherwise.
- Fuse databases: cross-checks against the manufacturer and, for values the manufacturer does not print, the sources themselves, held to the same two-source rule.
Many fuse websites copy or translate each other, so we count sources by lineage, not by address: two sites that reproduce the same table are one source. Every fuse description is written in our own words. On wider screens, each vehicle page’s title block shows how many sources its data was checked against and when it was last updated.
Two sources for every fuse
A fuse’s number, rating and description must agree across at least two independent sources. When sources disagree, the manufacturer’s document wins. Some manufacturers print ratings that no other source repeats; the manufacturer’s figure is the one we publish, and the research notes behind the page record it as resting on a single source.
Where a rating depends on the engine or the equipment fitted, the page stores the lowest listed rating and names the alternatives in the fuse’s description.
Where the layout comes from
A fuse table says what each fuse does. It does not say where the fuse sits. We take the layout of every box (rows, columns, empty sockets and the direction the numbers run) from a drawing: the owner’s manual plate, the manufacturer’s fuse card or cover label, a workshop drawing, or a photograph of the label or of the numbers moulded into the box.
A layout is never inferred from a count of positions. Sixteen fuses could sit four by four or two by eight, and a guess would put a correct number and rating in the wrong place. When no drawing of a box can be found, the box is left off the page until one is.
Where the manufacturer numbers each fuse carrier from 1, as Audi does with its lettered carriers, each carrier is its own diagram, numbered exactly as it is in the car. We never renumber carriers into one continuous sequence: those numbers would appear nowhere in the car.
Our own drawings
Every diagram is our own vector drawing, made from the facts the manufacturer’s drawing establishes. We do not copy any other site’s artwork. Each fuse type has its own drawing at its real proportions, from Mini, standard and Maxi blades and Micro 2 and Micro 3 blades to cartridge fuses, bolt-down fuses and fusible links, so the shape on the screen matches the part in your hand.
Ratings carry the colour code of their type. Blade fuses use the ISO 8820 colours (10 A red, 15 A blue, 20 A yellow and so on), and cartridge fuses and plug-in fusible links their own colour codes. Bolt-down fuses and the sealed links of a fusible-link block are drawn in one neutral colour, because none of the manufacturer documents we work from prints a colour code for them.
A fuse type we have not drawn before gets its own drawing before the box that uses it is published, rather than being shown as the nearest type we already had. That has been the rule since September 2026, and the boxes redrawn under it are listed in the corrections log.
Model years
Each model year has its own page. Manufacturers change fuse assignments during a production run, and most fuse websites reproduce only the latest edition of a handbook, so a fuse is accepted for a given year only when a source dated to that year supports it. We date handbook editions, fuse cards and labels by the manufacturer’s own printing dates, part numbers and edition codes, not by the year ranges databases give them.
A model year belongs to the generation that was the current model for most of it. Where a year straddles two generations, the page says which one it documents.
Checks before publishing
Fuse positions are never typed in by hand. Each box is defined as a grid of rows and columns, and every fuse is placed by its row and column on that grid. Every page then passes automated validation checks before it is published, and a page is refused if:
- it lists fewer than two sources;
- two fuses in one box share a number;
- a fuse has a type we have no drawing for;
- a description runs past the 255-byte limit;
- a fuse lies outside its box or overlaps another fuse;
- one element of a two-element fuse, such as a Micro 3, is missing its other half.
Each drawing is also checked by eye, on the rendered page or on its full-size image: fuses inside the housing, numbers and ratings legible, nothing clipped.
Corrections and reports
When a published value changes (a rating, a description, a fuse number, a position or a fuse type), we correct the page and add the change to the corrections log, with the date, the value before and after, and the document that settled it.
If something on a page does not match the fuse box in front of you, use the “Report a mismatch” button under the diagram, or write to [email protected] with the vehicle, the box and the fuse number. We check every report against the manufacturer’s documents, and a change it leads to goes into the corrections log, marked as reported by a reader.